您好,欢迎访问济南汇鑫彩钢 !为您提供济南彩钢板房,济南c型钢

全国服务热线

15253185838

15865282363

  • 3
  • 2
  • 1
    当前位置:首页>新闻中心>如何处理彩钢板房的漏水问题?

    如何处理彩钢板房的漏水问题?

    来源:http://www.jnsxcg.com/ 日期:2020-07-07 发布人:caigangban
      彩钢板房有通用性良好,易拆装,使用寿命长,高周转的特点。下面主要介绍彩钢板房子的漏水处理方法:
      Color steel room has good versatility, easy disassembly, long service life, high turnover characteristics. The following mainly introduces the water leakage treatment method of color steel plate house:
      首先,将彩钢板钢结构厂的脊的泄漏:主要原因脊的泄漏是:在脊波峰过高,和脊盖不能保证防水;垂直重叠并没有把胶或硅树脂,形成了间隙和泄漏;脊盖是纵向的搭接接头通过铆钉连接,铆钉由于热膨胀不充分,收缩强度,造成漏水打破;无堵塞在可动板的脊盖板和顶板之间架设,或插头被不规则地放置并脱落而形成水泄漏。
      First of all, the ridge leakage of the color steel plate steel structure plant: the main reasons for the ridge leakage are: the ridge crest is too high, and the ridge cover can not ensure waterproof; the vertical overlap does not put glue or silicone resin, forming a gap and leakage; the ridge cover is a longitudinal lap joint, which is connected by rivets, and the rivet is broken due to insufficient thermal expansion and shrinkage strength; No blockage is set up between the ridge cover plate and the top plate of the movable plate, or the plug is placed irregularly and falls off to form water leakage.
      解决方案:使屋脊盖更宽,并找到斜率较大点;打下水泥或在重叠硅胶;更换缝合钉;插头应该匹配平板式板,粘土或硅胶应放置起来,当插头被放下。
      Solution: make the roof wider and find the point with larger slope; lay cement or overlap silica gel; replace the stitching nails; the plug should match the flat plate, and the clay or silica gel should be placed when the plug is put down.
                    济南彩钢板房
      其次,彩钢板钢结构工厂的屋顶的檐板的泄漏:主要原因对于这部分的泄漏是:屋顶外板而没有泡沫栓安装,车顶外板不被下拉;壁外板的长度不充分,檐口部分不添加防水修整。 解决方法是:在安装屋顶面板时,泡沫塞应放置在同一时间,和顶板应该由30度被下拉;檐口应修剪根据目前的设计情况进行补充。
      Secondly, the leakage of the eaves on the roof of the color steel structure factory: the main reason is that the leakage of the roof is: the roof plate is not installed without foam plug, the roof plate is not pulled down, the length of the outer panel is not enough, and the cornice part is not waterproof and trimmed. The solution is: when installing the roof panel, the foam plug should be placed at the same time, and the roof should be pulled down by 30 degrees; the cornice should be trimmed according to the current design conditions.
      然后,彩钢板钢结构车间的沟槽部分的漏水:钢结构屋顶的排水沟深度小,并且在沟槽和车顶之间没有连续的防水结构。为在该部分的漏水的主要原因是:有在内侧沟槽的焊接接头的间隙,形成渗水;水槽和雨水管的直径太小,不匹配的植物的斜率长度;没有头板在沟槽处被的端部;如果排水沟的长度不够,水会流回到工厂。
      Then, there is water leakage in the groove part of the steel structure workshop: the drainage ditch depth of the steel structure roof is small, and there is no continuous waterproof structure between the groove and the roof. The main reasons for the water leakage in this part are: there is a gap between the welding joints in the inner groove to form water seepage; the diameter of the sink and rainwater pipe is too small to match the slope length of plants; there is no head plate at the end of the groove; if the length of the drainage ditch is not enough, the water will flow back to the factory.
      解决方法:适当增加排水沟的深度,使天沟雨水不超过搭接;内沟槽接头被焊接用于防水试验后,如果泄漏被发现,二次焊接是必需的;檐槽和雨水管设计的直径应通过计算在屋顶排水和确定;安装沟槽端头板;屋顶面板必须根据设计长度来构造。
      Solutions: properly increase the depth of drainage ditch, so that the rainwater in the gutter does not exceed the lap joint; after the inner groove joint is welded for waterproof test, if the leakage is found, secondary welding is necessary; the design diameter of eaves gutter and rainwater pipe should be determined by calculation in roof drainage; the groove end plate should be installed; the roof panel must be constructed according to the design length.
    

    咨询热线:15865282363    15253185838

    地址:济南市历城区荷花路王家闸村

    济南汇鑫彩钢

    济南汇鑫彩钢二维码

    济南汇鑫彩钢二维码